This group of colors with the polyamine and polyamide properties, such as resistance to abrasion, solvents and diluents power, high adhesion, high hardness and vulnerable convenient, has high mechanical strength, resistance to various chemicals, organic and inorganic. Epoxy paint due to its high resistance to moisture, friction and atmospheric and chemical agents; can be a good alternative to protective coatings. Epoxy paint is washable after drying completely and because of the flexibility resists against contrast to surface deformation of structures. And it's also very impactful.

      1. Middle Epoxy

These two-component coatings are polyamide-hardened epoxies and for the middle cover in a system are being used for external levels of tanks, Steel structures, Chemical factory pipelines, Refineries and Coastal areas by the sea.

Technical Specifications:

Stainless steel mica M.I.O is produced on the basis of polyamide epoxy resins and is presented in two parts with hardener. This type of epoxy primer with iron oxide compounds and anti-corrosion pigments is one of the most suitable coatings for metal structures and reservoirs for use in very humid and corrosive environments. It is also very resistant to acidic and alkaline environments. In general, this primer can be applied on the epoxy zinc-rich and zinc chromate or directly on metal surfaces, water canals, metal pipes and fittings, water and sewage systems, lining of dipped crude oil structures, salt solutions Used freshwater.

Usage:

Smooth the color components evenly with the mixer.
In accordance with the instructions on the colored packaging container, mix the first component of M.I.O with the second component, the hardener, and gradually mix it. Then, after 30 minutes, a special primer M.I.O is added to the epoxy. Note that after mixing M.I.O, the hardener and epoxy thinner are ready to be used up to a maximum of 4 hours. It needs to be explained that the M.I.O stainless steel epoxy is used as a primer and avoided using it without any sanitary conditions inside the drinking water reservoirs. Also, to get the best results for the next layer, it will be painted 24 to 48 hours after finishing the first layer coloring.
The surfaces should be free of any dust, rust, grease and moisture. M.I.O epoxy is applied directly to the metal. To achieve this, Sandblast operation is recommended for the SA 2 1/2 degree of purity.
Under normal conditions, a dye-colored spray with a thickness of 130 microns, a dry color, is obtained at a thickness of 100 microns.

       2. Epoxy Coating Color

Technical Specifications:

 Epoxy-based epoxy resin based on two-component, two-component epoxy resin and hardener for use on the zinc-epoxy layer, epoxy resin, metal, cement and wood surfaces. The epoxy layer is very resistant to atmospheric factors such as water, sunlight, acid and alkaline environments, oils, fats, and chemical detergents and other corrosive agents. This color is very useful in environments that are severely corrosive due to geographical circumstances or the problem of high sensitivity protection. This color is widely used in ports and ports, port structures, external walls of tanks and tanks, inland platforms, paper industry, structures and pipes in the chemical industry, refineries, petrochemical plants and power plants.

Usage:

Rinse the tools and tools carefully before use.
Mix the components of the paint evenly with the mixer.
In accordance with the instructions installed on the colored packaging containers, the first component (epoxy paint) is gradually mixed with the second component (hardener) and completely dissolved. Then, after 30 minutes, add a special epoxy paint thinner, we use the paint. Note that after mixing the paint, hardener and epoxy thinner, at 20 ° C, the paint is prepared and should be used before 8 hours.
The required level should be free of any dust, rust, grease and moisture. If the epoxy coating color is applied directly to the metal on a single layer, to achieve this, the sandblast operation is recommended to the degree of purity of SA 2 1/2.
Under normal conditions, the color of the dye is sprayed in a thickness of 81 microns, a dry color with a thickness of approximately 50 microns.
All paints and tools should be washed with a thinner after use at the end of each working day.

        3. Epoxy zinc chromate laminate

An epoxy paint with polyamide hardener where a large amount of zinc or zinc powder is used in it. This industrial paint that is type of lining and according to the National Standards of National Oil Company; it should contain at least a certain amount of zinc powder and also a certain percentage of solid weight.

 
         4. Epoxy zinc phosphate lining

Technical Specifications:

This primer is based on an epoxy resin and a zinc phosphate anti-corrosion pigment. This primer has good adhesion on the surfaces. Due to the use of non-toxic anti-corrosion pigment of zinc phosphate in drinking water systems with epoxy coatings, it can be used. This coating has a high coating capability and is easy to apply. It is used in the chemical industry, oil and power plants and on metal skeletons and ships, in-house and outbuildings, and in storage tanks, and is highly resistant to corrosive agents. It is a fast dry dye and is widely used in marine or industrial environments. This primer has a good adhesion to clean surfaces with hand tools. It should be noted that this primer is not suitable for protecting structures immersed in water or for coating primer containing zinc powder.

        5. Epoxy Liner Zinc Rich

Technical Specifications:

Zinc Rich Zinc Rich is produced on the basis of polyamide epoxy resins and is presented in three parts with Zine Dust and hardner hardeners.

Zinc Rich Epoxy Liner is a combination of excellent adhesion and epoxy hardness. This type of epoxy primer with zinc powder and excellent anti-corrosion compounds, with the formation of durable coating systems, is suitable for use with a wide range of treatments and one of the most suitable coatings for metal structures used in very humid and corrosive environments. is. It is also very resistant to acidic and alkaline environments. In general, this kind of primer can be directly applied to the metal surfaces of pipes and metal fittings, external walls of tanks and reservoirs in refineries and the paper industry in power plants and chemical industry, oil refineries and factories, sewage plants, ashtrays Submerged structures in crude oil, berths, deck and metal skeletons of ships, inland platforms and related structures are used.

Usage:

In accordance with the instructions on the colored packaging container, mix the first component of the resin with the second component, gradually mixing the powder on the Zine Dust. After completely mixing the first and second parts, gradually add the third, Hardner to it. Then, after 30 minutes, we add and use epoxy-specific thinner. Note that after mixing the color components, the hardener and epoxy tiner should be used up to a maximum of 8 hours at 20 ° C. It should be explained that in order to achieve the best result for the next layer, the second layer is painted 24-48 hours after finishing the first layer coloring.
The surfaces should be free of any dust, rust, grease and moisture, such as an epoxy mica layer of stainless steel directly applied to the metal. To achieve this, Sandblast operation is recommended for the SA 2 1/2 degree of purity.